SỬA XE NÂNG ĐIỆN KOMATSU

KOMATSU FB series Forklift Truck Fault Codes list

ERR-3082 Malfunction of the communication channel between the controller (right) stroke and the controller (left) stroke.

ERR-3084 Malfunction of the communication channel between the controller (right) stroke and the controller loading and unloading operations.

ERR-3281 Malfunction of the communication channel between the controller (right) stroke and the controller (left) stroke.

ERR-3284 Malfunction of the communication channel between the controller loading? Unloading operations and the controller (left) stroke.

ERR-5081 Malfunction of the communication channel between the controller (right) stroke and the controller loading and unloading operations.

ERR-5082 Malfunction of the communication channel between the controller (left) stroke and the controller loading and unloading operations.

ERR-5085 Malfunction of the communication channel between the proportional solenoid valve controller and the loading / unloading controller.

ERR-5087 Malfunction of the communication channel between the power supply controller and the controller loading and unloading operations.

ERR-5088 Malfunction of the communication channel between the controller loading? Unloading operations and the controller of the power source.

ERR-5211 Wrong control lever signal.

ERR-5212 Incorrect tilt control signal.

ERR-5213 Wrong ATT1 work equipment control lever signal.

ERR-5214 Wrong ATT2 work lever control signal.

ERR-5215 Incorrect signal from the ATT3 work equipment control lever.

ERR-5216 Wrong pressure sensor signal.

ERR-5217 Incorrect tilt sensor signal.

ERR-5218 Incorrect operation of proportional lift solenoid valve.

ERR-5219 Incorrect proportional tilt solenoid valve.

ERR-5220 Incorrect operation of the proportional solenoid valve of the ATT1 work equipment.

ERR-5221 Incorrect operation of the proportional solenoid valve of the ATT2 work equipment.

ERR-5222 Incorrect operation of the proportional solenoid valve of the ATT3 work equipment.

ERR-5292 Malfunction of the power supply of the proportional solenoid valve controller.

ERR-5293 Incorrect operation of the proportional solenoid valve controller.

ERR-5294 Wrong signal of the working machine sensor.

ERR-5295 Incorrect operation of the proportional solenoid valve controller.

ERR-5296 Communication error of the proportional solenoid valve controller.

ERR1 4-8110 Error in the communication process of the (right) stroke controller.

ERR1 8-8110 Communication error of the (left) stroke controller communication process.

ERR3 0-8110 Error in the communication process of the controller loading? Unloading operations.

ERR3 4-8110 Error in the communication process of the controller loading? Unloading operations.

ERR4 0-8110 Instrument panel communication process error.

ERR1 4-8120 Error transmitting / receiving data on the CAN bus controller (right) stroke.

ERR1 8-8120 Error sending / receiving data on the CAN bus controller (left) stroke.

ERR3 0-8120 Error of data transmission / reception via CAN bus controller loading and unloading operations.

ERR3 4-8120 Error of data transmission / reception on the CAN bus of the proportional solenoid valve controller.

ERR4 0-8120 Error transmitting / receiving data on the instrument panel CAN bus.

ERR1 4-8130 CAN communication channel malfunction between (right-hand) controller and instrument panel.

ERR1 8-8130 CAN communication link between the (left) controller and instrument panel is defective.

ERR3 0-8130 CAN communication link between the loading controller and the instrument panel.

ERR3 4-8130 CAN communication link between the proportional solenoid valve controller and the instrument panel.

ERR1 4-8140 Incorrect data transmission on the CAN bus of the (right) stroke controller.

ERR1 8-8140 Incorrect data transmission on the CAN bus controller (left) stroke.

ERR3 0-8140 Incorrect data transmission over the CAN bus controller loading and unloading operations.

ERR3 4-8140 Incorrect data transmission on the CAN bus of the proportional solenoid valve controller.

ERR4 0-8140 Incorrect data transmission over the instrument panel CAN bus.

ERR4 0-8314 CAN communication link between the (right) controller and instrument panel is defective.

ERR4 0-8318 CAN communication link between the (left) controller and instrument panel is defective.

ERR4 0-8330 CAN communication link between the loading controller and the instrument panel.

ERR4 0-8334 CAN communication channel malfunction between proportional solenoid controller.

Pan and dashboard.

ERR4 0-8510 Failure of the instrument panel CAN communication channel after the start switch is turned to the ON position

BẢNG MÃ LỖI XE NÂNG ĐIỆN KOMATSU

Bảng mã lỗi xe nâng điện Komatsu FB?? – 12 (xe nâng điện ngồi lái đời -12)

  • 2030 :
  • 3083 – 5083 :
  • 3054
  • 3056 :
  • 3062:
  • 3061:
  • 3082:
  • 3204:
  • 3010:
  • 3210:
  • 3282 – 5082:
  • 3257:
  • 4010:
  • 5055:
  • 5051:
  • 5052:
  • 5057:
  • 5216:
  • 5206 – 5207 – 5208 :
  • 5006 – 5007 – 5008 : 

Bảng mã lỗi xe nâng điện Komatsu FB??R? – 12 (xe nâng điện đứng lái đời -12)

  • E-01:
  • E-06:
  • E-07:
  • E-08:
  • E-09: 
  • E-10: 
  • E-11: 
  • E-12: 
  • E-13: 
  • E-14: 

  • E-16: 
  • E-51: 
  • E-52: 
  • K-54: 
  • E-56: 
  • E-57:
  • E-65: 
  • K-24/K-25: 
  • E-21: 
  • E-20: 
  • E-19: 
  • K-23: 
  • E-24,E-25: 
  • K-26: 
  • E-28: 
  • E-32: 
  • E-35:
  • E-36: 
  • K-37: 
  • K-13:
  • E05: 
  • E-26: 
  • E-27: 
  • E-28: 
  • E-39/E-43: 

SỬA XE NÂNG ĐIỆN TOYOTA

SỬA XE NÂNG ĐIỆN NICHIYU

Mã lỗi xe nâng NicHIYU

Error Message – Possible Cause – AdditionalMessage

A01 Contactor Main. Contactor to failed.

A02 Potentio-Steering Angle. Steering Angle Potentiometr error.

B10 Fuse-Travel. Blown main fuse.

B11 Fet-Travel. Travel FET module error (impossible to identifly which side). *Fail Operation* *Turn Off Key Switch*

B12 Sensor-Current Travel. Current sensor (traction motor) error.

B13 Directional SW. Directional microswitch error.

B14. Accelerator. Accelerator potentiometr error.*Turn Off Key Switch*

*Fail CAN BUS SYSTEM* CAN-BUS transmission error.

C21 FET-HYD.Hydraulic FET module error. *Fail Operation* *Turn Off Key Switch*

C22 Sensor Current HYD. Current sensor (hydraulic motor) error.

C23. Switch-Lift. Lift level microswitch error. Switch maybe bad, or the switch №2is activated earlier than switch №1

24 Potentio-Mast. Lift height parameter error (option)

D30 Fuse-EPS. Blown EPS fuse.

D31 Sensor EPS Torque. EPS sensor error.

D32 TR-EPS Main. Transistor error in the EPS controller.*Turn Off Key Switch*

E40 TR-AOS. Transistor Error in the AOS control board (option).

E41 Potentio-HYD. Lever. Error in the encoder for lift height.

*Fail Current Travel* Abnormal current (traction motor). *Turn Off Key Switch*

*Fail Current-HYD* Abnormal current (hydraulic motor)

SỬA XE NÂNG ĐIỆN JUNGHEINRICH

Một số mã lỗi xe nâng JUNGHEINRICH

Sub-division of function group F

0 Dystem: Overlappingfunction that cannot be assigned to any other function group

1 Travel

2 Hydraulics (load handling)

3 Steering and travel

4 Displays / controls, interface

5 Charger (either on-board or external charger)

6 Reserved

7 Reserved

8 Reserved

9 Special Functions

 

Sub-division of event group E

0 Fault reset or no fault

1 General fault /additional functions

2 Current

3 Voltage

4 Temperature

5 Hardware

6 Software

7 CAN motitoring

8 External fault

SỬA XE NÂNG ĐIỆN NOBLELIFT

Mã lỗi xe nâng hàng NOBLELift

NOBLELIFT Forklift FE3D series Truck Fault Codes DTC

Code display on the programmer – Code display on the instrument – Troubleshoot – Fault cause

 

Controller Overcurrent – 1.2 – controller current overload

1、motor outside U,V or Wconnection shour current

2、motor parameter mismatching

3、controller failure

 

Current Sensor Fault – 1.3 – Current sensor failure

1,motor U、V、W truck circuit,lead to current leakage

2,controller failure

 

Precharge Failed – 1.4 – Precharge failure

1,battery can’t charged

 

Controller Severe Undertemp – 1.5 – Controller temperature too low

1,The controller working environment is too harsh

 

Controller Severe Overtemp – 1.6 – Controller temperature too high

1,The controller working environment is too harsh

2,truck overloaded

3,the controller is wrongly assembled

 

Severe Undervoltage – 1.7 – Voltage too low

1, battery parameter is wrongly setted

2, non controller system power consumption

3, The battery impedance is too large

4, battery connection is disconnected

5,the fuse is disconnected, or main contactor is not connected

 

Severe Overvoltage – 1.8 – Voltage too high

1,Battery parameter is wrongly setted

2,The battery impedance is too large

3,Regenerative braking when the battery connection is disconnected

 

Controller Overtemp Cutback – 2.2 – Controller temperature too high, as a result the performance is not good

1, The controller working environment is too harsh

2,truck overloaded

3,the controller is wrongly assembled

 

Undervoltage Cutback – 2.3 – Voltage too low, as a result the performance is not good

1, battery power is insufficient

2, Battery parameter is wrongly setted

3, non controller system power consumption

4, The battery impedance is too large

5, battery connection is disconnected

6, the fuse is disconnected, or main contactor is not connected

Code display on the programmer – Code display on the instrument – Troubleshoot – Fault cause

 

Overvoltage Cutback – 2.4 – Voltage too high, as a result the performance is not good

1, during the process of regenerative braking, regenerative braking current lead the battery voltage to rise

2, Battery parameter is wrongly setted

3, The battery impedance is too large

4, when regenerative braking +5V Supply Failure 2.5 Controller output 5v, poer supply failre

1, external load impedance is too low

 

Digital Out 6 Failure – 2.6 – Drive 6 output overcurrent

1, external load impedance is too low

 

Digital Out 7 Overcurrent – 2.7 – Drive 7 output overcurrent

1, external load impedance is too low

 

Motor Temp Hot Cutback – 2.8 – The motor is too hot, as a result the performance is not good

1,The motor temperature reach or above the setted program alert temperature, lead the current output to reduce

2, motor temperature parameter is wrongly setted

3, If the motor has not used the temperature sensor, programming parameters

“Temp compensation” and “Temp cutback ”must be setted“ OFF”。

 

Motor Temp Sensor Fault – 2.9 – Motor temperature sensor failure

1, Motor temperature sensor is wrongly connecttedly

2, If the motor has not used the temperature sensor, parameter programming “MotorTemp Sensor Enable” must be setted “OFF”

 

Coil 1 Driver Open / Short – 3.1 – Drive 1 output linkng coil is open circuit or short circuit

1, connected load is open circuit or short circuit

2, connecting pin is stained

3, wrong wiring

 

Main Open / Short – 3.1 – Main contactor coil is open circuit or short circuit

1, connected load is open circuit or short circuit

2, connecting pin is stained

3, wrong wiring 

Code display on the programmer – Code display on the instrument – Troubleshoot – Fault cause

 

Coil2 Driver Open / Short – 3.2 – Drive 2 output linkng coil is open circuit or short circuit

1. connected load is open circuit or short circuit

2. connecting pin is stained

3. wrong wiring

 

EMBrake Open / Short – 3.2 – Electromagnetic brake coil is open circuit or short circuit

1, connected load is open circuit or short circuit

2, connecting pin is stained

3, wrong wiring

 

Coil3 Driver Open / Short – 3.3 – Drive 3 output linkng coil is open circuit or short circuit

1,connected load is open circuit or short circuit

2, connecting pin is stained

3, wrong wiring

 

Coil4 Driver Open / Short – 3.4 – Drive 4 output linkng coil is open circuit or short circuit

1,connected load is open circuit or short circuit

2, connecting pin is stained

3,wrong wiring

 

PD Open / Short – 3.5 – Proportional driving is open circuit or short circuit

1, connected load is open circuit or short circuit

2, connecting pin is stained

3, wrong wiring

 

Encoder Fault – 3.6 – Encoder failure

1,motor encoder is failure

2, wrong wiring

 

Motor Open – 3.7 – Motor is open corcuit

1, motor phase

2, wrong wiring

 

Main Contactor Welded – 3.8 – Main contactor adhesions

1, Main contactor contact welding

2, motor U or V disconnected or default phase

3,circuit that connecting B+ terminal will electricize the battery

 

Main Contactor Did Not Close – 3.9 – Main contactor is not closed

1, main contactor is not closed

2,Main contactor pin is oxydic, melted, or not stable when connected

3, external device electricize the battery

4, fuse is disconnected

 

Throttle Wiper High – 4.1 – Accelerator output is high

1,accelerator and potentiometer output voltage is too high

 

Throttle Wiper Low – 4.2 – Accelerator output is low

1,accelerator and potentiometer output voltage is too low

 

Pot2 Wiper High – 4.3 – potentiometer 2 output is too high

1,potentiometer 2 output voltage is too high

 

Pot2 Wiper Low – 4.4 – potentiometer 2 output is too low

1,potentiometer 2 output voltage is too low

 

Pot Low Overcurrent – 4.5 – potentiometer current is too low

1,potentiometer impedance is too low

 

EEPROM Failure – 4.6 – EEPROM failure

1,EEPROM storage failure 

Code display on the programmer – Code display on the instrument – Troubleshoot – Fault cause

 

HPD / Sequencing Fault – 4.7 – High pedal protection / operation order failure

1,The key start, interlock, direction, and the accelerator input order is wrongly setted.

2, Wiring, switch key, interlock, direction, or accelerator input failure

 

Emer Rev HPD – 4.7 – Emergenvy reverse high pedal protection

1,Emergency reverse operation is over, but the forward, reverse input and interlock of the accelerator are not resetted

 

Parameter Change Fault – 4.9 – Parameter change failure / wrong

1,In order to ensure the safety of the truck, some specific parameter changes must come into force after the key switch is restarted

 

OEM Faults – 5.1-6.7 – OEM failure(custom failure)

1,The user can define by themself the fault, use VCL code to note.

 

VCL Run Time Error – 6.8 – VCL running time is wrong

1,VCL code running time is overtime

 

External Supply Out of Range – 6.9 – Externial battery output is out og range

1, externial loading is between 5V and 12V , battery current is too big or too small

2, in the“inspection menu (Checking Menu)”, parameter is wrong, such as “ExtSupply Max”,“Ext Supply Min”

 

OS General – 7.1 – Operation system failure

1,internial controller failure

 

PDO Timeout – 7.2 – PDO overtime

1,CAN PDO information reception time exceeds PDOtime limition

 

Stall Detected – 7.3 – Motor stalling

1, Motor stalling

2, motor encoder failure

3, wrong connection

4, input motor encoder battery failure

 

Motor Characterization Fault – 8.7 – Motor matching failure

1, In the process of motor matching, code contrast:

0=normal

1= The controller receives the encoder signal, but impulse quantity is undefined. Please manually set pulse value

2=motor temperature sensor failure

3= motor high temperature response failure

4=motor overheating response failure

5= motor low temperature sensor failure

6=low voltage response failure

7=high pressure response failure 

8= Controller cannot detect the encoder signal, channel signals disappears

9= Motor parameter settings exceed the scope 

Code display on the programmer – Code display on the instrument – Troubleshoot – Fault cause

 

Motor Type Fault – 8.9 – Motor type failure

1,motor type(Motor Type) parameters exceed the scope

 

VLC/OS Mismatch – 9.1 – VCL/OS not matched

1,VCL and OS of the controller program are not matching

 

EM Brake Failed to Set – 9.2 – Electromagnetic setting failure

1, the truck still not move after the electromagnetic brake command is setted.

2, Electromagnetic brake braking force is too small

 

Encoder LOS (Limited Operating Strategy) – 9.3 – Encoder operation is limited

1,Because motor blocked or encoder failure, the limited operating state is activated

2, wrong wiring

3, truck stall

 

Emer Rev Timeout – 9.4 – Emergency reverse response time is overtime

1, because EMR Timer expires, so the emergency switch is actiated overtime

2, emergent reverse switch has been on the “on” position all the time

Illegal Model Number – 9.5 – Controller type is wrong

1, controller moder can recognize

2, software and hardware type are not matching

3, controller is damaged

SỬA XE NÂNG ĐIỆN NISSAN

Mã lỗi xe nâng NISSAN

NISSAN Forklift Truck Error Codes list

 

E03 VCM communication error

E04 ECM communication error

E05 DCM communication error

E06 HST communication error

E07 MP communication error

E08 TMS communication error

E21 Air flow meter error signal

E22 Water temperature sensor error signal

E23 Throttle sensor error signal

E24 Accelerator sensor error signal

E25 O2 sensor error signal

E26 O2 sensor heater error signal

E27 POS sensor error signal

E28 PHASE sensor error signal

E29 Self shutdown system diagnostic result error signal

E30 ECCS C/U error signal

E31 Electronic control throttle control error signal

E32 Overhear signal (STEP 1)

E33 Overheat signal (STEP 2)

E34 Spark system error signal

E35 LPG F/INJ disconnection diagnostic result signal

E36 LPG fuel pressure sensor diagnostic result signal

E38 LPG vaporizer diagnostic result signal

E39 Mast-high SW diagnostic result signal

E40 Oil pressure sensor diagnostic result signal

E41 Stop lamp SW error signal

F02 Battery voltage error

F57 Tilt backward solenoid error

F03 VCM communication error

F59 Tilt solenoid leak

F04 ECM communication error

F60 Attack-1A solenoid error

F05 DCM communication error

F62 Attach-1B solenoid error

F06 HST communication error

F64 Attach-1 solenoid leak

F07 MP communication error

F65 Attach-2A solenoid error

F08 TMS communication error

F67 Attach-2B solenoid error

F10 Lift lever neutral error

F69 Attach-2 solenoid leak

F11 Tilt lever neutral error

F70 Attach-3A solenoid error

F12 Attach-1 lever neutral error

F72 Attach-3B solenoid error

F13 Attach-2 lever neutral error

F74 Attach-3 solenoid leak

F14 Attach-3 lever neutral error

F75 Unload solenoid error

F16 Shift lever error

F77 Lift lock solenoid error

F17 Speed error

F7 Unload solenoid leak

E29 Self shutdown system diagnostic result error signal

F20 Lift lever error

F80 Knob position solenoid error

F22 Tilt lever error

F82 Tilt lock solenoid error

F24 Attach-1 lever error

F24 Knob position solenoid leak

F26 Attach-2 lever error

F85 T/M forward solenoid error

F28 Attach-3 lever error

F87 T/M backward solenoid error

F30 Main oil pressure sensor error

F89 T/M solenoid leak

F32 Lift oil pressure sensor error

F34 Speed sensor error

F36 Tire angle sensor error

F38 Tilt angle sensor error

F40 Steering error

F50 Lift up solenoid error

F52 Lift down solenoid error

F54 Lift solenoid leak

F01 Memory check error

F55 Tilt forward solenoid error

P03 VCM communication error

P04 ECM communication error

P05 DCM communication error

P06 HST communication error

P07 MP communication error

P08 TMS communication error

P22 Shift lever error signal